Search This Blog

Friday, October 10, 2025

Table Saw Throat Plate Fix

My table saw's throat plate is unsupported at the end next to the blade slot. It will flex down when I'm cutting thin strip and cause them to catch on the lip of the table top. This is a solution for that design flaw.
Throat plate unsupported here.
Three inches or so below that area is the top edge of the blade housing. I carefully measured how thick the housing was, how far it was below the table saw bed, and how thick the throat plate was at that spot.
1" Dowel to Support the Throat Plate
I cut a slot in the bottom end of a 1" dowel to slip snuggly over the blade housing.  The dowel now stands up to support the throat plate. 

A simple solution for a nasty design flaw.  I only wish I'd gotten around to solving this 10 years ago. 

Just note that if you need to tip//angle the blade you should remove the dowel before doing that. On my saw the housing the dowel rests on moves with the blade angle adjustment and will block that action as well as push up the throat plate if not removed. 

4D


 

Sunday, October 5, 2025

A Small Maple Box with a Contoured Lid.

This little box was cut from 4 corner scraps left over from a previous project.  The 4 corners were glued together to make a board with enough area for this 3" x 3" box. 

The lid was made from a scrap of Walnut wood I found in my scrap bin. The walnut was a bit thicker than I liked, so I cut the top to taper down to a thinner edge. 

Contoured Top
The bottom has a rabbet edge with a 3 degree slope for a fit that slips on easy but wedges tight.
Rabbeted edge
The lid overhangs the box by 1/16" to make it easier to pop the lid off. 
Overhanging Edge
The contrast between lid and box wasn't my original intent.  I started with a scrap of beech for the top but it worked loose while being cut and was ruined. A constant potential of using the CNC for making small parts.  I may darken the box with a walnut stain to lessen the contrast between box and lid. 

4D

 

Friday, October 3, 2025

Low Angle Dovetail Joint

I found this joint sample hiding in a box of CNC-cut joinery samples I made for students to consider when designing their project. 

For Low Angle Corners

One half slides into the other half.

Not quite as simple as it looks to cut
I endeavored to figure out how to connect wood pieces at any angle with a CNC-cut joint while I was teaching.  This is an extreme sample that I don't remember ever using for a student project.  The left half in the photo above is the complicated one to cut.  The sides taper in as the bottom of the dovetail is narrower than the top.  

This sample will return to the box I found it in to wait hopefully for the day when it can come out to inspire a real corner connection on an actual project. 

4D 

Wednesday, October 1, 2025

T-Square/Marking Gauge Add-On for a Small Ruler

Not all projects take a lot of time or a lot of wood.  A little scrap of Bubinga that was headed for the trash bin turned out to be the perfect material scrap for this project. 

Bubinga Scrap
Three CNC toolpaths.  Three vectors. Two router bits.  The slot that the ruler slides into was cut with a 1/8" t-slot bit.  The center area and curved edge were cut with the same 3/16" spiral down-cut end mill.  The blue friction tape keeps the ruler in place but still lets it slide out easy for compact storage. 
T-Square
This little block of wood turns a simple cheap ruler into a slightly more useful T-Square.  I plan to add this ruler/T-square to a drawing kit box project.  

A bonus feature is that the ruler can slide through.  This allows it to work as a marking gauge.

Marking Gauge
To insure that the ruler won't slide when using it I cut a recess under the friction tape for a small square nut, and added a thumb screw to lock the ruler in place.
Thumb Screw to lock it in place. 
 I'm delighted with how well it works and easy it was to make.  The bubinga scrap is delighted to be something useful.   ðŸ˜Š

4D

 

Tuesday, September 30, 2025

A Pencil Case. CNC Cut.

 A member of a router forum suggested I look into making a pencil box. 

A Pencil Shaped Box

As I designed the pencil shaped box I pondered what it might hold.  I concluded that a pencil box would most obviously hold a pencil.

Splits open to access a #2 pencil

This project though has provoke my runaway imagination to design a box that would hold much more. 

A pencil case at minimum only has to hold a single pencil.  I started out with a simple pencil shaped case that holds one pencil.  The hexagram body of the case was easy.  The conical tip was the challenge.  Sharpening the end of the case proved to be a challenge.  Half of a tapered cone cut from each side is what was needed. I figured out how to model the half cone, but not how to cut it.  I had to wait until both sides were done then clamped them together and vertically to use the moulding toolpath to cut the cone end. 

Alignment to the Y axis of my CNC for long skinny projects like this is a persistent challenge. Using my low profile vise to hold the first half of this single pencil case I took care to align the vise and board before cutting it. The vise was clamped down and not moved for the second half but clearly that was a mistake. The second half was slightly mis-aligned on one end.  Some sanding and a little trim router use cleaned up the mis-aligned edges.  

Many of these box projects have been excellent lessons on dealing with small projects and the precision needed.  Well worth the time.  Well worth the experience provided. 

4D

Wednesday, September 24, 2025

Red Zebra Wood Box with a Slide -in Lid

Poplar Lid

Mistakes are easy to make if you don't pay attention. This little Red Zebra Wood box with a Poplar slide-on lid looks fine, but the grain orientation of the lid should have been the same as the grain orientation of the box.  As such there will eventually be another lid for this box. 

The slot for the lid to slide into was cut with a t-slot bit. 

Lid Off.
The fit is good, but as wood likes to expand or contract across the grain when humidity changes I can't trust that the fit will always be the same. 
Slides in easily.
The red zebra wood block was dense and heavy.  It cut clean and nice.  The Poplar lid also cut nicely but wanted to split out on the edges. Toolpaths needed were simple to create.  The same vectors were used for both the box and the lid.  A small .003" allowance was used for the lid toolpaths so they wouldn't be too tight to slide in easily.

Alas I couldn't quit until the box had a new lid with the grain running left to right rather than up and down the lid.   Here is the box with a lid made from Ash wood. 
New Ash Lid.


Comments encouraged!

4D  



Monday, September 22, 2025

Walnut Box with a Hinged Lid

  I've had this block of Claro Walnut in my stash for a month or so. Recently it dared me to make something from it. 

Rough Block in Vise

It took a few steps to turn this block into a hinged box.  First step was to cut out the inside and then the outer edge using a 1/4" end mill. 

Inside and Outer Edge Done
Next step was to use a 3/16" end mill to cut slots for a hinge plate near each end. 
Hinge Slots Cut
The last step using the CNC was to round over the back edge using a 3/16" ball nosed bit. 
Rounded Back Edge
While in the vise I couldn't cut the bottom 1/2" of the perimeter so the box moved over to my trim router table to be flush cut.
Ready to Flush Cut
The flush cut bit struggled cutting the end grain sides and left some sanding to be done to even out the surface.
Flush Cut. Some Sanding Needed.
A lid and hinges were still needed.  For the lid I found an old strip of 3/4" thick walnut.  I cut off 10" or so, then ripped it  2" wide using my table saw. Next I used my bandsaw to slice it in half.   I took one half and ran it through my drum sander to sand it smooth and uniformly thick.  That strip was cut into 3 pieces, which I then glued together side by side.  This left me with a thin piece large enough to cut the lid from. 
Lid.  CNC Done
Next came the band saw to free the shape from the rough block.
Bandsaw to free the lid.
Then to my trim router table to clean up the edges. 
Flush Cut the Edges
Now trimmed close to the shape of the box, and waiting for hinge plate inserts.
Slots align.
Hinge plates are cut from 6mm thick Baltic Birch plywood.  Glued into the slots in the lid. Pinned into the box with 1/8"d steel pins.
Lid Attached
The lid opens 90 degrees but no more. Action is smooth but I may test if a little wax on the hinge plate makes a difference. 
Lid closed.
All machining processes done.   Some manual sanding and a final coat of finish or two or three is all that is left to do.   A fun project. A good mental exercise. A useful box. Fewer wood scraps to deal with.  4 wins!

Comments encouraged!
4D