Search This Blog

Showing posts with label Cherry wood. Show all posts
Showing posts with label Cherry wood. Show all posts

Saturday, August 9, 2025

Small Trays Made From Leftover Scraps

I have A CNC. I have a bottle of wood glue, and several clamps. I also have several small odd shaped wood scraps begging to be used for something useful.   

Small scraps glued up can make larger boards. Here are a few shallow wood dishes/trays all made from glued up scraps.  

This first oval dish was cut from three maple scraps glued together. I used my CNC to cut the top recess and rounded edge.  Then used my router table to bevel the side 11.25 degrees, and follow that up with a small 45 degree transition to the bottom.  

Oval Tray
This second tray was the best shape to make from two glued up corners saved from a hexagon table top cutout. 

Diamond Tray
This walnut version was made from several walnut scraps. Add in patching two screw holes with walnut dowels to increase the potential final size. For this one I used the modelling tool in Aspire to create the center recess. It also has a 45° chamfer on the bottom edge.  A rounded rectangle.
4" x 6"
This 4" x 4" Cherry example required several bit changes, and used the VCarve toolpath to make the crisp inside corners of the dish. It
 used up the left over corners from a round plant stand cutout. Its shape echoes the shape of the glued up corners. 
V-Carved Cherry Dish
Several bit changes were required.  Bits used (in order) were a 3/16" end mill to clear out the center area of the dish, then a 60 degree V-Bit to slope the sides and create the sharp inside corners. A 1/4" end mill cut a clearance path for the final bit and profile out the final shape.  Last bit used on the CNC was a side cutting V-bit to put a groove around the sides as shown below.

VCarved, V-cut, and beveled. 
As with all of these trays some follow up work was needed.  The waste perimeter was roughly cut off using my bandsaw.  A flush trim bit cleaned up the bottom edge on my trim router table.  Lastly a 45 degree chamfer bit beveled the bottom edge. 
Beveled bottom and side groove.
Lastly, an octagon dish. Made from one scrap board nearly 11" long and 2.6" wide.  It had a rough bark side.  I cut it in half and glued the good sides together to make a roughly 5" x 5" block close to 7/8" thick. The inner and outer sloped sides were 3D toolpaths.  The center of the top was a pocket toolpath to bring it down to the bottom of the inner sloped sides.  Hard maple with tight grain cut nicely on the CNC. 
Octa Dish

These are small examples of the value you can find from small scraps of wood left over from previous projects. Glue thin scraps together to make thicker boards that may be more useful. Any scraps with a straight edge can usually be glued up to make a larger board.  A trip across a jointer may be needed to face the edges for the best glue joint. I have a small benchtop jointer that is perfect for this task. Its small expose blade gap between tables make it safer than larger jointers with a larger expose blade gap to slide over. 

So save those odd scraps.  When boredom or inspiration strikes take a few and glue them up to make a larger board that can become something useful.  

Comment encouraged!
4D

Wednesday, July 9, 2025

A Table Lamp that Tips

Tipped to the Right.
Why a lamp that tips?   

Not for momentary joy or by a design mistake. With a way to keep the lamp leaning over at least a few obvious benefits become available.  Park the lamp on a corner of a table, then let it tip toward the middle to better illuminate the table surface.   Have kids that like to play on the floor?  Tip the lamp out to better illuminate the floor beside the table.  Using one or more 1"d steel balls and a rim of dished pockets you can move the Center Of Gravity around so the lamp will stay leaned in the direction the ball(s) are positioned at. Maximum lean angle is 12.5 degrees. 

Maximum Lean

This design consists of three wood parts.  A hub that the light hardware connects to. A simple center post. Lastly a domed base. Simple. Three parts. The lamp can tip but won't fall over. The base is a larger mimic of the top hub. The power cord runs up through the center post which is done in two halves. It exits the side of the base which is also cut in top and bottom halves.  The 1" steel balls were ordered from the jungle store, along with the 12mm threaded brass balls.  I used two halves each for the post and base to make it easy to route the power cable through. Base is 2.25" thick and the center post large diameter is 1.5". 

Almost Straight Up

A 12mm diameter brass ball screws down onto the harp. The shade ring with a 3/8" diameter hole rests on it and stays level no matter how far the lamp tips.  

I used the modelling tools in Aspire to make the pockets for the 1" steel ball on the curved surface of the base top. The moulding toolpath was used to shape all the other parts. Nine pockets evenly spaced around the perimeter allow just 3 steel balls to vary how far and in which direction the lamp tips.  

Undecided

This project, as many do, threw a few challenges to me when making the parts.  2-sided CNC projects must be perfectly aligned when flipped over.  Even when I think I have that challenge solved it is worth verifying alignment before each new cut. 

First try making the bottom of the base proved my design theory was wrong.  The curve was so flat the weight of the base itself was so heavy it wouldn't tip even with the steel balls all on one side.  

Second try I recut the bottom dome using 1/2 the previous radius.  It still was harder to rock the base than I want it to be.  Adding the light hardware, bulb, and shade might have made a difference so I added them to check. Testing proved the weight of the light hardware and shade weren't enough to make a difference.   

I had a cherry block that was large enough and thick enough to make a new base bottom. 1+5/16" thick.  Third try did indeed tip with the steel balls rather easily.   A bottom dome with close to a 6" radius center works well. 

This concludes my chase to see if this crazy idea works. I'll throw some maple stain and a top finish on the parts next time I have my finish table set up.   

Comments welcomed and appreciated. 

4D


 

Thursday, June 5, 2025

A Walnut and Cherry Wood Plant Stand

Walnut and Cherry
Often a project leaves useful scraps that also could be made into something useful.  That was the case with this simple plant stand. Some walnut salvaged from a previous design was re-configured to become the top. It became an eight inch diameter inverted dome cut from the glued up walnut.   

Walnut Top.  Ready for leg sockets

Lining up with the marked leg socket center

One socket cut.  

Four short sections of 5/8" diameter cherry dowels became legs. Each leg socket is perpendicular to the dome arc. The legs radiate out from the center of the arc. 

Standing up for the first time.

Deciding how simple or complex in detail the legs can be is a worthwhile iterative pursuit.  I've started with a simple cylinder with the bottom cut off to be flush to the surface it stands on. The sockets/mortises have a bump on their perimeter.  The legs ends have a notch to fit around the bump.  The reference orientation is what made it easy to cut the angle on the bottom of the legs as seen in the first photo.  

For detail I could add some plant inspired carving along the length of one or more leg.  I could simply roundover the ends or create more of a bullet shape or pencil tip shape.  I have the dowels connected but not yet glued into the top. It stands up to be observed and inspiring so this decision may be easier. If I do add more detail I'll post an updated photo.  With a plant on top to draw focus this little stand may be happy enough just supporting it rather than competing for attention.  ;)

A version with a cherry top and walnut legs:  Simple Plant Stand
A version with a white ash top and red zebra wood legs: Ash Plant Stand

Comments are welcomed and appreciated. 
4D

Saturday, April 13, 2024

TV Tray Table. Cherry. Refinement in Details.

Cherry.  5i
This is my 3rd TV Tray Table prototype.  Made from Cherry wood.  It demonstrates different details used with the same dual position geometry that the first two have.  Those two are here:

Ash Version

Red Oak Version

Ash, Cherry, Red Oak

The first two use threaded bolts into embedded nuts or barrel nuts to hold the outer legs to the top and the inner leg frame. They could come unscrewed in use as the frame is folded and unfolded. This Cherry wood version addresses that flaw and uses a new detail.  The bolt heads look the same but won't come unscrewed in use.

Pivot Bolts
The bolts pictured above are the pivot bolts for the outer leg connection to the top and inner leg frame. They slip through a hole in the outer leg and into the top's rear corners, or the inner leg frame sides. They are held there by an intersecting binding screw shaft. They can spin in place but won't unscrew themselves as the table folds or unfolds.  I was unable to find such a thing looking online, so I cut these from longer bolts using the rotary axis on my CNC. 
Binding Bolts.  18mm Shafts
I've used different strategies to tension the frame so it won't collapse.  Wire cable on the Ash version, and straps at the top in the Oak version are both complicated to make/install.  This Cherry wood version uses short 3/4" wide straps between the front and back legs. They are 5" below the pivot point to keep the legs from splitting apart.  The unique use and path of the straps adapts to both slanted and inside-out horizontal top positions. The strap location is just below where the top rests when the stand is folded up flat. A little serendipity in what was an arbitrary location choice. 
Folded Flat

The outer legs of this Cherry wood version run straight, with only a small bump over to the offset hole at the top.  A simple detail that might draw some attention.  The bump is neatly in plane with the slanted top.  

Slanted top
It is an interesting bump above the top when horizontal. 
Horizontal top.

This Cherry version uses a simple short strap with a grommet in both ends to handle the tension when the legs want to split apart. 

Grommet in strap end.
A binding bolt passes through the grommet inside each leg to retain the straps but lets the strap rotate to accommodate the angle it approaches each leg at. 
The straps slip into 1/8" wide slots. One edge of the slot is rounded over so the edge won't wear on the strap as it exits and wraps around the leg to head toward the other leg. 
Straps held by binding bolts
This Cherry table is so far my favorite of the three. Beautiful wood. Complimentary green straps. A pleasant presence. 


This design is patented. The details can vary, but the geometry that lets the table stand flat or turn inside out to be slanted down is the unique property. A fourth version, made from maple, can be found HERE.
 
For information on licensing the design please contact:
Sarah Nolting
Licensing Associate
Kansas State University Innovation Partners
(785) 532-3910
snolting@ksu.edu
www.k-state.edu/innovation-partners

Questions and comments are welcomed!
4D

 

Thursday, June 30, 2022

Coffee Tables with a Glass Top

These table designs are the outcome from an iterative sketching session.  The construction details are simple and style independent.  I've made 3 different styles of this system with different legs and wood choices that all are put together the same way.  The variations were inspired by a former student's research project. Her hypothesis was that age, gender, socio-economic status, and a few other factors would influence style-based buying choices.

I call this one Chéri.

Cherry Legs. Wax Finish

Simple Construction

Cherry Top.  Oil Finish
The legs of Chéri were also an outcome of their own iterative sketching session. The height of the foot is the same as the gap between the glass top and the wood top. The upper curve (a French curve) if continued down would end at the inside corner of the legs. I've made copies of this design out of hard maple with a birds eye center strip and red oak with a curly oak center strip. Both have found their own homes.  This cherry version was the original prototype.  The finish on the legs was an experiment which I don't care for. Plywood templates of both the front and side curves of the legs make it rather easy to duplicate the legs.  The two that I sold had a nicer glass top with an ogee edge to compliment the French ogee edge profile on the wood top.  Having a transparent top encourages featuring more interesting wood grain on the shelf below. The shelf is also a good place for seasonal or thematic décor. 

This one is Savanna.  Where Zebras roam.

Zebra Legs

Simple Construction

Zebrawood Center
I used a photo of Zebras to help inspire the shape of the legs. Zebra wood is rather busy when used in wide panels, so the top is a center strip of Zebrawood with quarter sawn white oak strips on both sides that the legs appear to run through. 

The third design was simpler with square post legs and made from red oak. "Country" might best describe the style. Red oak with a cherry stain. My parents chose it out of the three designs and it was handed down to my oldest sister. She enjoys it. I don't have a photo of this one but below is a rendered image of what it looks like without a glass top.

All versions normally have silicon pads atop the legs which both keeps the glass from being bumped out of position, and covers the top of the bolts that keep the top and bottom sections of the legs attached to the wood top.  

So which design do you prefer?  I'd love to know and if you don't mind sharing your age and gender that data would add to the data the student collected.  

4D
Comments and questions welcomed and encourage.  


Sunday, April 10, 2022

Accessory Table. 5ft.

Tables with a round top ask for a nice base that looks great from all angles, and contributes to rather than distracts from the overall aesthetic.

This little 5 footed table stands sturdily and proud. Made from Cherry wood, and finished with Danish Oil.  The top has a French Ogee profile to add a little style. 

Legs are made from 3 parts joined together with mortises and tenons. The legs all dovetail into a 5 sided center hub at the top and lower down. Leg parts were rough cut then trimmed to identical shapes with a template and pattern bit on the router table.   

A nice stance.

No bad views.
The design evolved through iterative sketches. No design of mine falls directly onto paper. An initial sketch might be nice, but iteration never fails to improve upon the aesthetic appeal. How the design is made also evolves through iteration. 

Comments welcomed and appreciated!

4D

Elliptable. A Table Composed of Ellipses.

Ellipses are simple to draw using most CAD software.  They are also fairly simple to cut out using a CNC.  I designed and made this table before I had a CNC I could use though. It evolved from an idea I had to invert a simple ellipse drawing jig.  To test the jig out I used it to swing the wood panels through a router bit on my router table in elliptical paths. Every ellipse in the design was cut with the same jig.   The legs have a slight rounded edge that echos the ellipse shape of the top above. 

Cherry hardwood


















The top came from the center.




















Ellipse Jig

The legs join together with dovetails. This design is a good example of detail continuity.

An Ellipse Drawing Jig

Comments welcomed and appreciated.

4D